It’s one of the worst feeling knowing your Ethernet cable has disconnected. You’re sitting in a meeting and you need to send an urgent email, but instead, you have to stand up, walk out of the room, and find a new location where your ethernet cable can get online. If this happens often, then it might be time to invest in a quality Ethernet cable and some tips on how to prevent your Ethernet cable from disconnecting.
Why Is My Ethernet Cable Disconnecting?
The most common reason for an Ethernet cable to disconnect is when you’re using a surge protector. Using a surge protector allows your device to receive power and transmit signals, but it often doesn’t have enough power to do both at the same time. If you use a surge protector that has an outlet plugged into it, then this may cause your ethernet cable to disconnect.
Another reason for an Ethernet cable to disconnect is low-quality cables or a problem with the plug/jack in the wall. In order to prevent this from happening, make sure that you replace your cables every few years and never use cheap third-party cables because they may not be of good quality and could potentially cause issues with your connection.
If you are connecting two devices via a USB port on the computer, then make sure to always connect the device with the USB first before powering on the computer or other device connected via Ethernet cable.
If you’re using two computers (or two routers) that are wired together and one of them loses power in between, then there can sometimes be an issue with data ports getting disconnected on one of these devices. Make sure both devices have power until they’re configured correctly by following these steps:
How To Prevent Your Ethernet Cable From Disconnecting
1. Make sure your Ethernet cable is firmly plugged into a good location.
2. Locate your Ethernet port on the router/switch and make sure it’s not blocked off by furniture or anything else.
3. Avoid using old, worn-out, or damaged cables.
4. Buy an Ethernet cable expressly designed for use with your modem/router and avoid cheap, generic cables that might not be compatible with your equipment.
5. If you have access to a power outlet, plug the Ethernet cable into the power outlet so that it doesn’t disconnect from the wall socket when you’re in a hurry.
10 Tips for Preventing an Ethernet Cable from Disconnecting
1. Connect your ethernet cable to the back of your computer’s Ethernet port
2. Ensure that your computer is fully plugged in to the wall outlet
3. Ensure that you have a physical connection between the Ethernet cable and the back of your computer by ensuring that there is no dust on the Ethernet connector
4. One way to ensure a solid physical connection between the two devices is to place it in a zip lock bag and then tie it off with a rubber band so that the rubber band touches both ends of the wire
5. It can also help if you use an Ethernet patch cord instead of a standard Ethernet cable
6. The last thing you can do is to try using different cables, such as coaxial cables or fiber optic cables so that you are able to see whether or not this helps make the connection more stable
7. You can also try moving around where your device plugs into the wall outlet, changing outlets, moving outlets, or moving cords around just for good measure
8. All in all, it might be time to invest in an ethernet surge protector as well
9. Finally, if all else fails then maybe it’s time to invest in an ethernet extender
Test your cable with a continuity tester
The first thing you should do is test your cable with a continuity tester. A continuity tester allows you to test the wires in your Ethernet cable. If one of the wires disconnects, then the tester will show an open circuit on the screen and allow you to trace down which wire has gone bad. Additionally, these testers allow you to test that all of the wires are installed properly.
Test your cable with a wireless device
As a first step, make sure your Ethernet cable is working properly by testing it with another device that has wireless capabilities. If the cable works on a wireless device, then you know it’s just a problem with the port or your connection that needs to be fixed.
If you’re still having problems with your Ethernet cable disconnecting, try these steps:
Check the port on your router to make sure it’s not faulty
If you’re using your computer to connect to the internet, then it’s likely that your ethernet cable is plugged into a port on your router. You can check the port on your router to make sure it isn’t faulty. If you are able to plug a second ethernet cable into another port, then you know that there’s nothing wrong with the first port.
Make sure you have enough power for your computer and router
Do you have enough power for your computer and router? Make sure this is the case by checking that your power supply provides enough wattage for the device. If it doesn’t, then you should consider upgrading your power supply or getting a new one altogether.
Digital devices require a lot of power, and if you’re not going to be able to provide it, then the connections will disconnect.
Check the point of entry to your router, whether it be in a wall or on the floor
If you’re using an Ethernet cable to connect your desktop to your router, then it’s important for you to make sure that the point of entry is secured. If the point of entry is on the floor and not in a wall, then make sure that the Ethernet cable is anchored to something sturdy so that it doesn’t get pulled or yanked out.
